- Home
- Honeywell 51308099-100 Interface Module
Oferta
Honeywell 51308099-100 Interface Module
No reviews
In stock!
- Part Number: 51308099-100
- Brand: Honeywell
- Type: Interface Module
- Dimensions: 15.8x10.5x3.5cm
- Country of Origin: USA
- Barcode: 8537101190
Compartir
Additional Specifications
| Color / Pattern |
|
| Power Source |
|
Descripción del Producto
Configured for digital logic execution and remote serial data telemetry within DCS and PLC architectures, the Honeywell 51308099-100 (51308099-100 Industrial Control Module) provides direct physical/electrical execution. The multi-configuration module bridges field-level sensing arrays and high-current actuator circuits natively at the hardware tier to maintain synchronized process monitoring loops.
Hardware Specifications
| Parameter | Specification |
|---|---|
| Model | 51308099-100 |
| Brand | Honeywell |
| Series | Honeywell DCS / PLC Architecture Component |
| Origin | United States |
| Weight | Standard compact panel-mount module mass |
| Dimensions | Compatible with standard Honeywell marshalling enclosure footprints |
| Nominal Supply Voltage | 24 V DC (Control and PLC interface configurations) |
| Rated Insulation Voltage | Up to 250 V AC maximum |
| Rated Continuous Load Current | 10 A continuous output threshold |
| Maximum Switching Capacity | Up to 15 A peak (variant-dependent boundary) |
| Supported Input Frequency | 40 to 60 Hz (AC control configurations) |
| Digital Input Density | Up to 10 hardware channels |
| Digital Output Density | Up to 6 hardware channels |
| Relay Output Configuration | 2 x Single Pole Double Throw (SPDT) isolated relay contacts |
| Communication Interface | RS-485 serial interface port |
| Supported Line Protocols | Modbus RTU (variant dependent) |
| Enclosure Protection Rating | Up to IP65 sealed field enclosure standard |
| Operating Temp Range | -20 to +60 deg C (PLC configurations) / -20 to +70 deg C (Industrial control configurations) |
| Relative Humidity Limits | 5% to 95% RH, non-condensing |
| Product Type | Digital I/O Cards |
Process Control & DCS Instrumentation Network Topology
- Isolated Relay Execution and Multi-Drop Protocol Routing The module incorporates twin SPDT mechanical relay junctions that handle high-capacity inductive and resistive load switching up to 10 A continuous at 250 V AC. An integrated RS-485 transceiver transforms raw digital input states into native Modbus RTU register frames, allowing real-time telemetry distribution straight to master DCS nodes parallel to localized hardware interlock sequences.
- Channel-to-Channel Isolation and Thermal Threshold Management Internal optocoupler arrays isolate the 10 digital input lines from the main 24 V DC processing logic core, suppressing common-mode voltage spikes and high-frequency inductive noise. The internal circuit components are optimized for low standby power consumption, preventing localized heat build-up inside tightly packed IP65 environmental housings over the maximum -20 to +70 deg C operating band.
Frequently Asked Questions
Q: What programmatic or electrical faults manifest if the RS-485 termination resistor is omitted in a multi-drop topology?
A: Leaving the ends of the RS-485 communication line un-terminated causes high-frequency signal reflections back down the transmission wire. This echo distorts the Modbus RTU voltage waveforms, triggering immediate packet CRC errors, transmission timeouts, and intermittent node dropouts inside the supervisory PLC communication registers.
Q: Can the internal SPDT relay contacts be hot-swapped or serviced independently if the contacts fuse?
A: No, the SPDT relay mechanisms are permanently soldered directly onto the multi-layer internal printed circuit board assembly. Fusing or pitting of the contacts due to inductive back-EMF spikes requires complete isolation and replacement of the entire 51308099-100 module to restore reliable logic operations.
Have a question?
