{"product_id":"honeywell-05704-a-0131-relay-interface-card","title":"Honeywell 05704-A-0131 Relay Interface Card","description":"\u003cp\u003eConfigured for multi-loop detector interfacing in industrial control platforms, the \u003cstrong\u003eHoneywell 05704-A-0131\u003c\/strong\u003e (\u003cstrong\u003e05704-A-0131\u003c\/strong\u003e Relay Interface Card) provides direct physical and electrical execution of detector-to-control card signal routing.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003e05704-A-0131\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eHoneywell\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eSystem dependent\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e0.5 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e12.2 × 5.2 × 13.2 cm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003eIndustrial ambient range\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003e3.5 W (typical) \/ 6.5 W (max)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eI\/O Capacity\u003c\/td\u003e\n\u003ctd\u003e12 x SPCO, 4 x SPST\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eProcess Control and DCS Instrumentation Characteristics\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e4-20 mA HART loop protocol:\u003c\/strong\u003e The interface card architecture supports the routing of detector signals that may originate from HART-enabled loops. It maintains the signal continuity required to pass secondary diagnostic data through the relay interface to the host DCS, ensuring no loss of field device visibility.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eChannel-to-channel isolation:\u003c\/strong\u003e The design incorporates electrical isolation between the four detector loop inputs and the output relay stages. This is necessary to prevent ground potential variations or transient surges from a single detector loop from propagating across the interface card or into the main control backplane.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCold junction compensation (CJC):\u003c\/strong\u003e The card is designed to operate within high-density control racks. Its thermal design ensures that local components do not experience excessive heat soak, which protects the calibration accuracy of adjacent temperature-monitoring modules that rely on precise CJC execution.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFOUNDATION Fieldbus \/ Profibus PA connectivity:\u003c\/strong\u003e The card serves as a deterministic relay interface, ensuring that discrete output states triggered by fieldbus-connected controllers are executed with minimal propagation delay, maintaining synchronous system response for mission-critical interlocks.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Can the relay logic be modified after installation?\u003c\/p\u003e\n\u003cp\u003eA: Yes, relay operation is selectable. The interface supports configuration for Latching\/Non-Latching states as well as Energized\/De-Energized (fail-safe) modes via onboard jumpers or software settings, depending on the specific system requirements.\u003c\/p\u003e\n\u003cp\u003eQ: Is the 2.5 mm2 field terminal capacity compatible with standard stranded cabling?\u003c\/p\u003e\n\u003cp\u003eA: Yes, the field terminals accept up to 2.5 mm2 (14 AWG) wiring, supporting both solid and stranded conductors. Ensure that ferrules are utilized when terminating stranded wires to maintain contact integrity and prevent stray strands from causing short circuits between adjacent terminals.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting:\u003c\/strong\u003e Secure the relay interface card onto the designated backplane or mounting rail. Ensure the Expansion Relay Card is properly seated onto the Quad Relay Interface Card to guarantee reliable inter-card communication.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGrounding:\u003c\/strong\u003e Bond the card chassis to the cabinet earth bus. A robust, low-impedance connection is mandatory to ensure the efficacy of internal isolation and to suppress electromagnetic interference (EMI) generated by inductive relay switching.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWiring:\u003c\/strong\u003e Maintain strict separation between detector loop input wiring and high-voltage power output wiring. Route field wiring through dedicated ducts, keeping a minimum distance of 150 mm from AC lines or VFD cabling to prevent inductive noise injection into the low-voltage signal paths.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Honeywell","offers":[{"title":"Default Title","offer_id":47979432902846,"sku":"05704-A-0131","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0725\/1145\/5422\/files\/screenshot_2026-07-07_16-12-19_95e23288-2ec5-4ae8-add8-88232dddd267.png?v=1783415727","url":"https:\/\/www.autooiltech.com\/products\/honeywell-05704-a-0131-relay-interface-card","provider":"AutoOilTech Limited","version":"1.0","type":"link"}