{"product_id":"general-electric-is200jpdfg1a-power-distribution-board","title":"General Electric IS200JPDFG1A Power Distribution Board","description":"\u003ch2\u003eGE IS200JPDFG1A Power Distribution Board\u003c\/h2\u003e\n\u003cp\u003eConfigured for floating‑bus DC distribution in Mark VIe platforms, the \u003cstrong\u003eGE IS200JPDFG1A\u003c\/strong\u003e provides regulated routing of redundant 125 V DC inputs, fused AC paths, and diagnostic feedback through PPDA‑linked sensing circuits.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eParameter\u003c\/th\u003e\n\u003cth\u003eSpecification\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eIS200JPDFG1A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eGE\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eOrigin\u003c\/th\u003e\n\u003ctd\u003eUnited States\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003eNot specified\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDimensions\u003c\/th\u003e\n\u003ctd\u003eNot specified\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eOperating Temp\u003c\/th\u003e\n\u003ctd\u003eNot specified\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePower Consumption\u003c\/th\u003e\n\u003ctd\u003eNot specified\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCore Performance Indicators\u003c\/th\u003e\n\u003ctd\u003eRedundant 125 V DC inputs; fused AC routing; PPDA diagnostic feedback; floating DC bus; JP1 jumper‑selectable centering resistance\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eBackplane Bus Communication Velocity Licenses\u003c\/h3\u003e\n\u003cp\u003eWithin GE’s Mark VIe architecture, the JPDF board aligns with deterministic backplane timing used for power‑distribution signaling. Although the board is not a communication module, its routing paths maintain predictable propagation delays across DC and AC distribution circuits, supporting stable I\/O density scaling. Firmware flash compatibility resides at the PPDA I\/O pack level; the JPDF board itself provides fixed electrical behavior without programmable logic.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eQ: What is IS200JPDFG1A?\u003c\/strong\u003e A: It is a DC power distribution board used in Mark VIe systems to route redundant 125 V DC and fused AC power to downstream modules.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eQ: How to obtain this PDM?\u003c\/strong\u003e A: The board is typically sourced through GE turbine‑control distributors. (Commercial details omitted per technical‑only requirement.)\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eQ: Can JP1 be closed on multiple JPDF modules?\u003c\/strong\u003e A: No. Only one JPDF module should have JP1 closed when providing centering resistance for the floating DC bus.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eMount the module vertically on the metal back base within the PDM cabinet to ensure correct connector alignment.\u003c\/li\u003e\n\u003cli\u003eBond the JPDF sheet metal to protective earth (PE) to stabilize floating‑bus sensing and reduce AC noise coupling.\u003c\/li\u003e\n\u003cli\u003eRoute DCHI and DCLO battery inputs with correct polarity and strain relief; verify circuit‑breaker and line‑filter wiring before energizing.\u003c\/li\u003e\n\u003cli\u003eMaintain separation between AC feed paths (JAF1) and DC distribution wiring to minimize induced noise.\u003c\/li\u003e\n\u003cli\u003eEnsure JZ2 and JZ3 connectors are fully seated when linking DACA modules; partial engagement can cause intermittent DC return paths.\u003c\/li\u003e\n\u003cli\u003eUse the 50‑pin ribbon cable from P1 to PPDA P2 when diagnostic feedback is required; confirm cable routing avoids sharp bends or tension.\u003c\/li\u003e\n\u003cli\u003eFollow GEH‑6632 installation practices for grounding, cabinet bonding, and fuse‑branch verification.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"General Electric","offers":[{"title":"Default Title","offer_id":47908618731710,"sku":"IS200JPDFG1A","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0725\/1145\/5422\/files\/screenshot_2026-06-30_10-41-59.png?v=1782787591","url":"https:\/\/www.autooiltech.com\/products\/general-electric-is200jpdfg1a-power-distribution-board","provider":"AutoOilTech Limited","version":"1.0","type":"link"}