{"product_id":"ge-is200tdbth6a-discrete-input-output-terminal-board","title":"GE IS200TDBTH6A Discrete Input\/Output Terminal Board","description":"\u003ch2\u003eGE IS200TDBTH6A Discrete Input\/Output Terminal Board\u003c\/h2\u003e\n\u003cp\u003eConfigured for contact input and relay output handling in Mark VIe architectures, the \u003cstrong\u003eGE IS200TDBTH6A\u003c\/strong\u003e (\u003cstrong\u003eIS200TDBTH6A\u003c\/strong\u003e terminal board) provides direct electrical interfacing for 24 discrete channels and 12 relay outputs through hardware‑filtered input conditioning and isolated wetting‑voltage groups.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eParameter\u003c\/th\u003e\n\u003cth\u003eSpecification\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eIS200TDBTH6A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eGE\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eOrigin\u003c\/th\u003e\n\u003ctd\u003eUnited States\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003eNot specified\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDimensions\u003c\/th\u003e\n\u003ctd\u003e17.8 cm × 33.02 cm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eOperating Temp\u003c\/th\u003e\n\u003ctd\u003e−30 to +65 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePower Consumption\u003c\/th\u003e\n\u003ctd\u003e+5 V DC (board logic)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCore Performance Indicators\u003c\/th\u003e\n\u003ctd\u003e24 discrete channels; hardware input filter; 12 relay channels; AC rejection 12 V RMS; surface‑mount PCB\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eProfinet \/ EtherNet\/IP Deterministic Networks\u003c\/h3\u003e\n\u003cp\u003eWithin GE’s Mark VIe control architecture, the TDBT terminal board aligns with deterministic backplane communication timing used by Profinet and EtherNet\/IP networks. Although the board itself is passive, its routing paths support stable I\/O density scaling by maintaining predictable propagation delays across discrete channels. Firmware flash compatibility resides at the controller level; the terminal board provides fixed electrical behavior without programmable logic.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eQ: Can the terminal board be hot‑swapped while the rack is energized?\u003c\/strong\u003e A: Terminal boards are not designed for hot‑swap. Removal or insertion should occur only when the associated rack segment is de‑energized to avoid transient loading on the backplane.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eQ: How does the hardware filter affect input response time?\u003c\/strong\u003e A: The hardware filter suppresses high‑frequency noise and surges. It introduces a small, fixed delay typical of passive filtering networks but does not alter nominal contact‑closure detection.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eQ: Does AC voltage rejection impact DC wetting‑voltage operation?\u003c\/strong\u003e A: No. The 12 V RMS AC rejection is applied to noise suppression. DC wetting‑voltage operation remains unaffected when supplied within the nominal 24\/48\/125 V DC ranges.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eMaintain correct landing of wetting‑voltage conductors to each isolated input group.\u003c\/li\u003e\n\u003cli\u003eBond shielded wiring at a single termination point to reduce induced noise on contact inputs.\u003c\/li\u003e\n\u003cli\u003eRoute relay wiring separately from high‑current solenoid or motor circuits to avoid impedance coupling.\u003c\/li\u003e\n\u003cli\u003eVerify that the option‑card connector is fully seated before energizing the panel.\u003c\/li\u003e\n\u003cli\u003eInspect terminal screws periodically to ensure long‑term mechanical stability.\u003c\/li\u003e\n\u003cli\u003eFollow GEH‑6721L installation practices for grounding, rack alignment, and cable strain relief.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"General Electric","offers":[{"title":"Default Title","offer_id":47908557815998,"sku":"IS200TDBTH6A","price":650.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0725\/1145\/5422\/files\/general-electric-is200tdbsh2a-discrete-simplex-card-azry4flq2l0.png?v=1759055713","url":"https:\/\/www.autooiltech.com\/products\/ge-is200tdbth6a-discrete-input-output-terminal-board","provider":"AutoOilTech Limited","version":"1.0","type":"link"}