{"product_id":"abb-dsta-133-i-o-module","title":"ABB DSTA 133 I-O Module","description":"\u003cp\u003eThe \u003cstrong\u003eABB DSTA 133\u003c\/strong\u003e, also cataloged as the \u003cstrong\u003e3BSE018312R1\u003c\/strong\u003e I-O Module, operates as a dedicated hardware component for localized field-to-backplane junction distribution within Advant Master Process Control System platforms. Configured as a direct interface terminal block, this connection unit establishes precise physical and electrical interfaces to route multi-channel analog input fields into the S100 I\/O rack subsystem.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eDSTA 133\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eABB\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eSweden\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e0.25 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003eCompliant with WEEE Category 5 small equipment specifications\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e-10 to +55 deg C typical industrial environment range\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003ePassive termination routing layout; zero active power draw\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCore Product Type\u003c\/td\u003e\n\u003ctd\u003eI-O Module Termination Units\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eExchange Unit Model\u003c\/td\u003e\n\u003ctd\u003e7650055-778\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTarget Board Pairing\u003c\/td\u003e\n\u003ctd\u003eAnalog Input Board Integration\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSystem Compatibility\u003c\/td\u003e\n\u003ctd\u003eAdvant Controller 450, MasterPiece 200\/1, S100 I\/O, 800xA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHS Code\u003c\/td\u003e\n\u003ctd\u003e85389091\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eBackplane Bus Communication Velocity and System Integration\u003c\/h3\u003e\n\u003cp\u003eThe DSTA 133 functions strictly to preserve raw backplane bus communication velocity across high-density conversion nodes by maintaining low-impedance copper signal paths between external field wiring transmitters and internal analog logic registers. By facilitating clean parallel path mappings directly to the matching input board, the unit assists the host CPU in optimizing overall physical I\/O density scaling routines without encountering propagation distortion or parasitic phase delays. The module architecture guarantees seamless firmware flash compatibility at the controller level, allowing the host Advant Master or 800xA system to continuously run onboard signal diagnostics and loop tracking loops through the termination point.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Does the DSTA 133 interface block place an electrical load demand on the primary S100 I\/O backplane power supply?\u003c\/p\u003e\n\u003cp\u003eA: No, the DSTA 133 is configured as a passive termination interface. It maps physical line paths directly to the input module logic without drawing operational current from the subrack backplane power rails.\u003c\/p\u003e\n\u003cp\u003eQ: Can a damaged DSTA 133 module be safely swapped while the system controller is executing online runtime tasks?\u003c\/p\u003e\n\u003cp\u003eA: Hot-swapping the connection unit while field transmitters are actively powered is prohibited. Severing the connection block disrupts live analog loops, drops channel voltage readings to absolute zero, and triggers immediate diagnostic system faults within the active controller rack.\u003c\/p\u003e","brand":"ABB","offers":[{"title":"Default Title","offer_id":47586603499710,"sku":"DSTA 133","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0725\/1145\/5422\/files\/screenshot_2026-05-28_16-11-59_8512b685-7b09-439d-893b-cb2fea6ada2f.png?v=1779960415","url":"https:\/\/www.autooiltech.com\/products\/abb-dsta-133-i-o-module","provider":"AutoOilTech Limited","version":"1.0","type":"link"}