{"product_id":"ge-is200stcih6add-contact-input-terminal-board","title":"GE IS200STCIH6ADD Contact Input Terminal Board","description":"\u003ch2\u003eGE IS200STCIH6ADD Contact Input Terminal Board\u003c\/h2\u003e\n\u003cp\u003eConfigured for contact‑signal acquisition in Mark VIe I\/O networks, the \u003cstrong\u003eGE IS200STCIH6ADD\u003c\/strong\u003e (\u003cstrong\u003eIS200STCIH6ADD\u003c\/strong\u003e contact input terminal board) provides 24‑channel dry‑contact interfacing with nominal 24, 48, or 125 V dc excitation. The board supports DIN‑rail or flat‑plate mounting and includes suppression circuitry for surge and high‑frequency noise.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eParameter\u003c\/th\u003e\n\u003cth\u003eSpecification\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eIS200STCIH6ADD\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eGE\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eOrigin\u003c\/th\u003e\n\u003ctd\u003eUnited States\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003eNot specified\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDimensions\u003c\/th\u003e\n\u003ctd\u003e15.9 cm × 10.2 cm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eOperating Temp\u003c\/th\u003e\n\u003ctd\u003e-30 to 65 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePower Consumption\u003c\/th\u003e\n\u003ctd\u003eNot specified\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCore Performance Indicators\u003c\/th\u003e\n\u003ctd\u003e24 contact inputs; 24\/48\/125 V dc excitation; noise‑suppression circuitry; DIN‑rail or flat mounting; surface‑mount construction; shield‑termination bracket; 18 AWG wiring compatibility\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eProfinet \/ EtherNet\/IP Deterministic Networks\u003c\/h3\u003e\n\u003cp\u003eWithin Mark VIe architectures, the STCI board aligns with deterministic I\/O‑pack timing used for synchronous contact‑state interrogation. Although the board itself is passive, its suppression components maintain stable propagation intervals under high‑frequency interference. I\/O density scaling is achieved through fixed 24‑channel allocation, while firmware flash compatibility resides entirely at the I\/O processor level; STCI hardware characteristics remain fixed across all variants.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eQ: Can the IS200STCIH6ADD be hot‑swapped?\u003c\/strong\u003e A: No. The board must be installed or removed only when the associated cabinet segment is de‑energized to avoid transient excitation‑voltage loading.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eQ: How does the I\/O processor validate contact inputs?\u003c\/strong\u003e A: It monitors excitation voltage, interrogates the board’s ID device, and performs diagnostic forcing of all inputs to the open state. Any input failing this test is forced to failsafe (open) and flagged as a fault.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eQ: Are there wiring restrictions for shielded cables?\u003c\/strong\u003e A: Yes. Shields must terminate at a dedicated bracket to prevent ground‑loop formation and reduce EMI coupling.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eMount the board on a DIN‑rail carrier or bolt‑on sheet‑metal assembly with the plastic insulator installed.\u003c\/li\u003e\n\u003cli\u003eUse 18 AWG conductors for contact wiring to ensure proper terminal‑block engagement.\u003c\/li\u003e\n\u003cli\u003eTerminate cable shields at the designated bracket to maintain isolation from signal conductors.\u003c\/li\u003e\n\u003cli\u003eMaintain separation between contact wiring and high‑energy conductors to reduce induced noise.\u003c\/li\u003e\n\u003cli\u003eVerify correct seating of connectors before energizing the excitation system.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"General Electric","offers":[{"title":"Default Title","offer_id":48161068482750,"sku":"IS200STCIH6ADD","price":320.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0725\/1145\/5422\/files\/general-electric-is200srtdh2acb-drl-termbd-rtd-j2rkfm22rdq.png?v=1759132300","url":"https:\/\/www.autooiltech.com\/ar\/products\/ge-is200stcih6add-contact-input-terminal-board","provider":"AutoOilTech Limited","version":"1.0","type":"link"}