{"product_id":"emerson-pr6423-01h-030-con021-eddy-current-displacement-transducer-system","title":"Emerson PR6423\/01H-030 + CON021 Eddy Current Displacement Transducer System","description":"\u003cp\u003eThe \u003cstrong\u003eEmerson PR6423\/01H-030 + CON021\u003c\/strong\u003e, also cataloged as the \u003cstrong\u003ePR6423\/01H-030\u003c\/strong\u003e Eddy Current Displacement Transducer System, operates as a dedicated hardware component for non-contact shaft vibration and axial displacement monitoring within AMS machinery protection networks.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003ePR6423\/01H-030 + CON021\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eEmerson \/ EPRO\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eGermany \/ Global Manufacturing Facility\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e0.45 kg (combined sensor and converter assembly)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003eM10 x 1 threaded probe body, 3 meters cable length\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e-35 deg C to +180 deg C (sensor), -35 deg C to +150 deg C (cable\/connector)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003ePowered via -23 VDC to -32 VDC loop supply\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMeasurement Range\u003c\/td\u003e\n\u003ctd\u003e2 mm (80 mils)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eIncremental Scale Factor\u003c\/td\u003e\n\u003ctd\u003e8 V\/mm +\/-5% (203.2 mV\/mil)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOutput Signal\u003c\/td\u003e\n\u003ctd\u003e4-20 mA, 0-10 V, or +\/-10 V (configurable via CON021)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eProtection Rating\u003c\/td\u003e\n\u003ctd\u003eIP66 (sensor tip assembly)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003e4-20 mA HART Loop Protocol and Channel Isolation\u003c\/h3\u003e\n\u003cp\u003eThe signal processing circuitry of the CON021 converter translates raw high-frequency oscillator variations into standardized outputs supporting 4-20 mA HART loop protocol integration. Channel-to-channel isolation architecture prevents ground loops and electrical interference from propagating across multi-channel vibration monitoring racks. Internal cold junction compensation and regulated negative voltage supply rails maintain signal integrity over long transmission distances up to 30 meters total cable length. The configuration guarantees zero drift and linear scaling compliance across dynamic frequency responses spanning 0 Hz to 20,000 Hz.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: What is the required gap voltage calibration target during initial mechanical setup?\u003c\/p\u003e\n\u003cp\u003eA: The probe gap should be adjusted mechanically until the static output voltage reaches the nominal midpoint target corresponding to the linear operating range of the CON021 converter.\u003c\/p\u003e\n\u003cp\u003eQ: Can the 3 meters integral cable length be shortened or extended in the field?\u003c\/p\u003e\n\u003cp\u003eA: No. The probe assembly, integral cable, and CON021 converter module are factory-calibrated as a matched electrical system. Altering cable length changes total electrical capacitance and invalidates calibration accuracy.\u003c\/p\u003e\n\u003cp\u003eQ: What is the minimum target shaft diameter required for accurate measurement?\u003c\/p\u003e\n\u003cp\u003eA: The rotating shaft target diameter must be at least 25 mm to prevent edge effect errors on the electromagnetic eddy-current field generated by the 8 mm probe tip.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eEnsure the mounting hole is threaded cleanly with an M10 x 1 tap, and deburr the entry point to prevent physical damage to the PEEK probe tip during mechanical seating.\u003c\/li\u003e\n\u003cli\u003eMaintain a minimum radial clearance distance of 25 mm between adjacent probe tips to eliminate mutual electromagnetic cross-talk between monitoring channels.\u003c\/li\u003e\n\u003cli\u003eRoute the non-armored PTFE signal cable away from high-power motor leads and variable frequency drive output conduits, securing the shield drain wire at the designated panel ground bar.\u003c\/li\u003e\n\u003cli\u003eVerify loop DC resistance and static output voltage using a high-impedance digital multimeter prior to system energization and machinery startup.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"EMERSON","offers":[{"title":"Default Title","offer_id":48179988463806,"sku":"CON021+PR6423\/01H-030","price":650.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0725\/1145\/5422\/files\/EZ1080-05-00-010_57cec58d-f00e-4e8e-b98a-793fcb828f54.png?v=1784627656","url":"https:\/\/www.autooiltech.com\/ar\/products\/emerson-pr6423-01h-030-con021-eddy-current-displacement-transducer-system","provider":"AutoOilTech Limited","version":"1.0","type":"link"}